Nason ful thane 2k urethane single stage mixing ratio - Nason Finishes recommends using a ratio of 8:1/2:4, or 8 parts of Nason base coat to 1/2-part base coat activator to 4 parts base coat reducer. Failure to mix the paint properly can clog your spray gun. If you’re using aerosol cans, the paint should be properly mixed in the can for you, so skip this step. What is the mixing ratio for Nason paint?

 
I sprayed over sanded 2K primer. Before I sprayed I wiped the panel with 70% rubbing alcohol. The fisheyes/solvent pop didn't show up until an hour or two after the last coat. I sanded down the panel with 220 and some of the craters are fairly deep but non of them go to the primer. Could it be oil in the air section of the gun?. Novo x won

MIXING COMPONENTS Mix 2 parts NasonXL Basecoat Color to 1 part NasonXL Reducer. Thin to spray viscosity of 16 secs with #4 Ford @ 77°F/25°C for spraying. Option for longer re-coating: Add 5% hardener to premixed basecoat Component Volume NasonXL Basecoat Color 2 NasonXL Reducers 1 (447-65 Fast, 447-75 Medium, 447-85 Slow) Package SizesParts by Volume. 491-10™. 2. 483-01™ / 483-02™. 1. Viscosity. 20-22 seconds in a Zahn #2 cup. Pot Life. 12 hours at 70°F.Item#: NAS 400-01 01. Ful-Thane® 400-01 Factory Packaged Black provides outstanding durability for automobiles, trucks, and commercial vehicles. This remarkable finish provides excellent gloss, chip resistance and ease of application. To 1 gallon of Ful-Thane® 2K Urethane, add 1 pint of 483-15™ Catalyst. Reduce with 1 quart Ful-Base® 441 ...MIXING COMPONENTS Ful-Thane® HS Urethane Topcoat (IG Quality) Ful-Base® 430-XX Tints Ful-Thane® HS 435-95™ Urethane Binder Ful-Thane® 483-52™ Activator Ful-Thane® 483-54™ Accelerator (Required) MIX RATIO Combine the components by volume (3:1). Mix thoroughly prior to activation. Component Volume I just got myself all confused and need some clarification. :embarrass Nason Ful-Thane 2K Urethane is a single stage finish but it says 2K in the title, is it just a single stage? Do I have to shoot a clear over it if I’m using a metallic color? The last question is if I use a siphon gun, what tip size and psi works well with it.18-21 seconds in a Zahn #2 cup. 4 hours at 70°F. Solid colors: Apply 1 medium wet coat, flash to tack, apply 1 full wet coat. Metallic colors: Apply 2 medium-wet coats. Allow to flash 5-10 minutes between coats. Apply a third and final “mist” coat to even the metallic. Refer to the product Technical Data Sheet for complete directions for use.A 2.8 lb/gal (340 g/l) VOC compliant, urethane single-stage topcoat that provides good quality and performance and features a wide range of sparkling metallic and rich solid colors. Features Solventborne Good quality Wide color range Product Details Available Sizes Mixing Instructions Application Instructions ApplicationDescription. A National Rule compliant, Factory Package Snow White urethane single stage topcoat designed with superior hardness development for better cycle time, and improved metallic control providing thousands of cleaner, more vibrant colors. Ful-Thane 2K Urethane is the Nason brand’s premium single-stage paint that is easy to apply and ...CODE DESCRIPTION REMARKS MIX RATIO HARDENER REDUCER MAX APPLIED VOC (LE) IB Quality Ful-Thane® 2K Single Stage Topcoat 8:1:2 483-15™ 441-2X 5.0 lb/gal IC Quality Ful-Base® Single Stage Topcoat 8:1:2 483-08™ 441-2X 5.0 lb/gal ID Quality Ful-Cryl® II Single Stage Topcoat 8:1:2 483-11™ 441-2X 5.0 lb/galCODE DESCRIPTION REMARKS MIX RATIO HARDENER REDUCER MAX APPLIED VOC (LE) IB Quality Ful-Thane® 2K Single Stage Topcoat 8:1:2 483-15™ 441-2X 5.0 lb/gal IC Quality Ful-Base® Single Stage Topcoat 8:1:2 483-08™ 441-2X 5.0 lb/gal ID Quality Ful-Cryl® II Single Stage Topcoat 8:1:2 483-11™ 441-2X 5.0 lb/galItem#: NAS 401-20 01. Designed to enhance the depth and color of Ful-Thane® factory packaged colors, Ful-Thane® 2K Urethane single-stage colors and Ful-Cryl® II mix colors. Gallon. Approved customers please Log In or Register for approval.Oct 23, 2013 · 8-1-2 ratio is for Nason Ful-Thane single stage . Check the label on the can of color for the correct ratio and hardener numbers . If the lower door is your only problem why not just respray the door to the side mldg just above the handle . A 2.8 lb/gal (340 g/l) VOC compliant, urethane single-stage topcoat that provides good quality and performance and features a wide range of sparkling metallic and rich solid colors. Features Solventborne Good quality Wide color range Product Details Available Sizes Mixing Instructions Application Instructions ApplicationApproved customers please Log In or Register for approval. Axalta Nason Ful-Base Reducer 441-21 Medium Quart. Item#: NAS 441-21 -4. Reducer for Nason topcoats and urethane primers. Approved customers please Log In or Register for approval. Axalta Nason Fulthane Activator 1/2 Pint. Item#: NAS 483-15 -6.Single Stage Topcoat ; Thinner ; ... FUL-THANE URETHANE SS BINDER "IS" 2.8 Gallon. ... SELECTSEAL 2K URETHANE SEALER - BLACK Gallon. Item #: 422-52 01.To enhance depth of color and provide a custom look, Ful-Thane® 401-20™ 2K Integrated Clear may be used. Mix one quart of catalyzed and reduced Ful-Thane® 401-20™ 2K Integrated Clear with one quart of activated and reduced color. Both are mixed 8:1:2. Do not use Ful-Thane® 401-20™ 2k Integrated Clear as a topcoat clear.Axalta Nason Fulthane 2K Urethane Quart Mix. Item#: NAS IB -4. Ful-Thane® Urethane, one of the distinct paint qualities in the versatile Ful-Base® Multi-Leg Color System, provides an easy-to-apply, single-stage finish. Ful-Thane® offers outstanding durability for automobiles, trucks and commercial vehicles.Do not use under any urethane paints other than Nason® Ful-Thane® 2K Urethane. Use same reducer for Bond-Seal™ as recommended for the Nason® single-stage topcoat to be applied. DRY TIMES To topcoat (for Nasco™ and Ful-Base® Topcoats): 10 minutes, but within 8 hours PHYSICAL PROPERTIES All Values Ready To Spray Max.To enhance depth of color and provide a custom look, Ful-Thane® 401-20™ 2K Integrated Clear may be used. Mix one quart of catalyzed and reduced Ful-Thane® 401-20™ 2K Integrated Clear with one quart of activated and reduced color. Both are mixed 8:1:2. Do not use Ful-Thane® 401-20™ 2k Integrated Clear as a topcoat clear.SelectPrime™ 483-87™ 2K Activator (Mid-Temp) SelectPrime™ 483-88™ 2K Activator (Hi-Temp) MIX RATIO Combine the components by volume (4:1). Mix thoroughly prior to activation. Component Volume SelectPrime™ 421-17™ / 421-19™ 2K Urethane Primer 4 SelectPrime™ 483-88™ / 483-87™ 2K Activator 1 TINTABILITY Not recommended POT LIFEDupont Fleet book, page by page. If you are on a PC click on any of the. images and the images will pop up. You can hit next and the whole or most of the page will turn into a gallery.Parts by Volume. IF Quality. 8. 483-00™. 1/2. 441-2X. 4. Viscosity. 20-21 seconds in a Zahn #2 cup.Mix Ratio Combine components and mix thoroughly. Three Component System Parts by Volume Nason® FulThane® 2K Topcoat (IB quality) 8 Nason® 483-15™ Activator 1 Nason™ FulBase® Reducer 2 Add 2-4 oz. of Nason® 483-18 Accelerator to activated gallon to decrease tape time by 50%.Ful-Thane® Urethane, one of the distinct paint qualities in the versatile Ful-Base® Multi-Leg Color System, provides an easy-to-apply, single-stage finish. Ful-Thane® offers outstanding durability for automobiles, trucks and commercial vehicles. Ful-Thane® 2K urethane is also available in Ful-Thane® 400-XX High Volume Factory Packages.Mix Ratio Combine components and mix thoroughly. Three Component System Parts by Volume Nason® FulThane® 2K Topcoat (IB quality) 8 Nason® 483-15™ Activator 1 Nason™ FulBase® Reducer 2 Add 2-4 oz. of Nason® 483-18 Accelerator to activated gallon to decrease tape time by 50%.8-1-2 ratio is for Nason Ful-Thane single stage . Check the label on the can of color for the correct ratio and hardener numbers . If the lower door is your only problem why not just respray the door to the side mldg just above the handle .Show's how to do a complete automotive paint job using inexpensive materials such as old school lacquer primer from Auto Body Master and Nason Ful-Cryl II Ac...Ful-Base® 430-XX Tints Ful-Thane® 435-91™ 2K Urethane Binder Ful-Thane® 483-15™ 2K Urethane Activator Ful-Base® 441-20™ Reducer (Low-Temp) Ful-Base® 441-21™ Reducer (Mid-Temp) Ful-Base® 441-22™ Reducer (High-Temp) MIX RATIO Combine the components by volume (8:1:2). Mix thoroughly prior to activation. Component Volume Ful-Thane ...Ful-Thane 2K Urethane Binder (IB Quality) (PDF 362.8 kB) Nason Ful-Base Enamel Topcoat (IC Quality) (PDF 258.0 kB) Nason Ful-Cryl II 2K Acrylic Enamel Topcoat (ID Quality) (PDF 334.5 kB)In this video I finish up a series of door repair videos by painting the repaired panel using Nason Ful-Cryl II Single Stage Acrylic Enamel. Nason Ful-Thane ...CODE DESCRIPTION REMARKS MIX RATIO HARDENER REDUCER MAX APPLIED VOC (LE) IB Quality Ful-Thane® 2K Single Stage Topcoat 8:1:2 483-15™ 441-2X 5.0 lb/gal IC Quality Ful-Base® Single Stage Topcoat 8:1:2 483-08™ 441-2X 5.0 lb/gal ID Quality Ful-Cryl® II Single Stage Topcoat 8:1:2 483-11™ 441-2X 5.0 lb/galSearch Nason Search Nason. Safety Data Sheets. Print; Print page to PDF; Nason - Safety Data Sheets - English. Downloads. Type ...Reference page for Mixing Nason Automotive Topcoats and Undercoats. For those that use Nason Automotive Paint Products, having a mixing chart is a must. The below charts, include both topcoats and undercoat products. Topcoats being your colors in singles stage to base-coats, as well as your clears. Undercoats are your primers and sealers.Application. Solid Colors: Add 1 part of RTS Ful-Thane 2K Urethane Single Stage (NIB) or Ful-Cryl 2K Acrylic Single Stage (NID) color to 1 part RTS VS4500 2K Urethane Integrated Clear during the last and final coat of the single-stage color. Effect Colors:Single Stage Topcoat ; Thinner ; ... FUL-THANE URETHANE SS BINDER "IS" 2.8 Gallon. ... SELECTSEAL 2K URETHANE SEALER - BLACK Gallon. Item #: 422-52 01.I just got myself all confused and need some clarification. :embarrass Nason Ful-Thane 2K Urethane is a single stage finish but it says 2K in the title, is it just a single stage? Do I have to shoot a clear over it if I’m using a metallic color? The last question is if I use a siphon gun, what tip size and psi works well with it.Thane® 2K Urethane single-stage colors and Ful-Cryl® II mix colors. The products referenced herein may not be sold in your market. Please consult your distributor for product availability. MIXING COMPONENTS Ful-Thane® 401-20™ 2K Urethane Integrated Clear Ful-Thane® 2K 483-15™ 2K Urethane Activator Ful-Base® 441-20™ Reducer (Low-Temp)Ful-Thane® Urethane, one of the distinct paint qualities in the versatile Ful-Base® Multi-Leg Color System, provides an easy-to-apply, single-stage finish. Ful-Thane® offers outstanding durability for automobiles, trucks and commercial vehicles. Ful-Thane® 2K urethane is also available in Ful-Thane® 400-XX High Volume Factory Packages.Oct 23, 2013 · 8-1-2 ratio is for Nason Ful-Thane single stage . Check the label on the can of color for the correct ratio and hardener numbers . If the lower door is your only problem why not just respray the door to the side mldg just above the handle . JFG Discussion starter · Feb 25, 2009. Hi! I'm planning to paint my daily car as a practice before going on more serious project. I'm planning to use the Nason Ful-thane 2k urethane (solid black) with maybe a clearcoat Nason 497 (depending on your comments). The car (a small Nissan Sentra 1996 ) is already black so it's gonna be black on black.JFG Discussion starter · Feb 25, 2009. Hi! I'm planning to paint my daily car as a practice before going on more serious project. I'm planning to use the Nason Ful-thane 2k urethane (solid black) with maybe a clearcoat Nason 497 (depending on your comments). The car (a small Nissan Sentra 1996 ) is already black so it's gonna be black on black.MIX RATIO . Combine the components by volume (4:1:1). Mix thoroughly prior to activation. Component Volume . Ful-Thane 2K Urethane Single Stage Color (NIB Quality) 4 . Axalta VS5300 Urethane Activator 1 . Axalta VS5160 / VS5170 / VS5180 / VS5190 Reducer 1 435-00, 435-01 Ful-Thane Binders VS5300 Urethane Activator VS5160, VS5170, VS5180, VS5190 ...Single Stage Topcoat ; Thinner ; ... FUL-THANE URETHANE SS BINDER "IS" 2.8 Gallon. ... SELECTSEAL 2K URETHANE SEALER - BLACK Gallon. Item #: 422-52 01.MIXING COMPONENTS Ful-Thane® HS Urethane Topcoat (IG Quality) Ful-Base® 430-XX Tints Ful-Thane® HS 435-95™ Urethane Binder Ful-Thane® 483-52™ Activator Ful-Thane® 483-54™ Accelerator (Required) MIX RATIO Combine the components by volume (3:1). Mix thoroughly prior to activation. Component Volume Spraying a single stage metallic is not fun with any paint.Make sure you have enough air pressure,even spray pattern,and you need to make dead even passes to have the proper metallic layout.Nason is a great paint IMO.I would bet money its the same as the higher end or discontinued Dupont products in a different can.I would use a base/clear system for any metallic paint.If you use more reducer, or over reduce it, you can use the 2k primer as a sealer as well. MTK isn't a primer. It's a SS topcoat urethane that can be cleared or mixed with clear on the final coat.Axalta Nason Fulthane 2K Urethane Quart Mix. Item#: NAS IB -4. Ful-Thane® Urethane, one of the distinct paint qualities in the versatile Ful-Base® Multi-Leg Color System, provides an easy-to-apply, single-stage finish. Ful-Thane® offers outstanding durability for automobiles, trucks and commercial vehicles.Dupont Fleet book, page by page. If you are on a PC click on any of the. images and the images will pop up. You can hit next and the whole or most of the page will turn into a gallery.18-21 seconds in a Zahn #2 cup. 4 hours at 70°F. Solid colors: Apply 1 medium wet coat, flash to tack, apply 1 full wet coat. Metallic colors: Apply 2 medium-wet coats. Allow to flash 5-10 minutes between coats. Apply a third and final “mist” coat to even the metallic. Refer to the product Technical Data Sheet for complete directions for use.MIX RATIO Combine the components by volume (4:1:2). Mix thoroughly prior to activation. Component Volume Ful-Thane® 2K Urethane Topcoat (IS Quality) 4 Ful-Base® 483-56™ Low VOC Activator 1 Ful-Base® 441-60™ / 441-66™ / 441-68™ Reducer 2 ADDITIVES Fisheye Eliminator Add ½ to 2 oz Nason® 495-02™ Low VOC Fisheye Eliminator per ready ...MIXING COMPONENTS Ful-Thane® HS Urethane Topcoat (IG Quality) Ful-Base® 430-XX Tints Ful-Thane® HS 435-95™ Urethane Binder Ful-Thane® 483-52™ Activator Ful-Thane® 483-54™ Accelerator (Required) MIX RATIO Combine the components by volume (3:1). Mix thoroughly prior to activation. Component Volume K. kmoses Discussion starter · Feb 10, 2012. I sprayed the entire car with Nason Select-Prime 421-19 2K urethane primer and block sanded to P400 dry. I then sprayed the two front fenders, the hood and the trunk lid with Nason Ful-Poxy 491-16 Epoxy primer blocked sanded dry to P400 and wet sanded to P500 ( I am planning to spray the whole car ...Ful-Thane® Urethane, one of the distinct paint qualities in the versatile Ful-Base® Multi-Leg Color System, provides an easy-to-apply, single-stage finish. Ful-Thane® offers outstanding durability for automobiles, trucks and commercial vehicles. Ful-Thane® 2K urethane is also available in Ful-Thane® 400-XX High Volume Factory Packages. Thane® 2K Urethane single-stage colors and Ful-Cryl® II mix colors. The products referenced herein may not be sold in your market. Please consult your distributor for product availability. MIXING COMPONENTS Ful-Thane® 401-20™ 2K Urethane Integrated Clear Ful-Thane® 2K 483-15™ 2K Urethane Activator Ful-Base® 441-20™ Reducer (Low-Temp)Oct 23, 2013 · 8-1-2 ratio is for Nason Ful-Thane single stage . Check the label on the can of color for the correct ratio and hardener numbers . If the lower door is your only problem why not just respray the door to the side mldg just above the handle . 18-21 seconds in a Zahn #2 cup. 4 hours at 70°F. Solid colors: Apply 1 medium wet coat, flash to tack, apply 1 full wet coat. Metallic colors: Apply 2 medium-wet coats. Allow to flash 5-10 minutes between coats. Apply a third and final “mist” coat to even the metallic. Refer to the product Technical Data Sheet for complete directions for use.Nason Full-Thane lists the ratio as 8:1:2 My mix cups have 8:1:1 Using the '5' scale the distance between the 1:1 is 3/8". Will adding 3/8" mark to the last column give me an 8:1:2 ratio? View attachment 1715764917Nason 496-00 SelectClear 2K Urethane Spot Clear. Vendor: Mahopac Auto Paint. $146.99. $123.00. Nason 483-70 Selectclear 2K Activator-Mid-Temp (2.5L) Vendor: Mahopac Auto Paint. $171.99. $140.00. Nason 475-00 SelectClear 2K Urethane High Image Clear.Axalta Nason Fulthane 2K Urethane Quart Mix. Ful-Thane® Urethane, one of the distinct paint qualities in the versatile Ful-Base® Multi-Leg Color System, provides an easy-to-apply, single-stage finish. Ful-Thane® offers outstanding durability for automobiles, trucks and commercial vehicles. Please contact store for the proper price suffix for ...Ful-Base® 430-XX Tints Ful-Thane® 435-91™ 2K Urethane Binder Ful-Thane® 483-15™ 2K Urethane Activator Ful-Base® 441-20™ Reducer (Low-Temp) Ful-Base® 441-21™ Reducer (Mid-Temp) Ful-Base® 441-22™ Reducer (High-Temp) MIX RATIO Combine the components by volume (8:1:2). Mix thoroughly prior to activation. Component Volume Ful-Thane ...It is a single stage, but there is a clear your can mix with it or another to spray after it. dont use clear on single stage. you just put the single stage on, color sand with 1500 or 2000 grit, then buff to shine. if you want to use a clear coat, then you need to use a base/clear setup. personally, i wouldnt use a single stage paint on a car ...Ful-Base® 430-XX Tints Ful-Thane® 435-91™ 2K Urethane Binder Ful-Thane® 483-15™ 2K Urethane Activator Ful-Base® 441-20™ Reducer (Low-Temp) Ful-Base® 441-21™ Reducer (Mid-Temp) Ful-Base® 441-22™ Reducer (High-Temp) MIX RATIO Combine the components by volume (8:1:2). Mix thoroughly prior to activation. Component Volume Ful-Thane ...Parts by Volume. 491-16™. 1. 483-19™. 1. Viscosity. 16-22 seconds in a Zahn #2 cup. Pot Life. 24 hours at 70°F.MIX RATIO . Combine the components by volume (4:1:1). Mix thoroughly prior to activation. Component Volume . Ful-Thane 2K Urethane Single Stage Color (NIB Quality) 4 . Axalta VS5300 Urethane Activator 1 . Axalta VS5160 / VS5170 / VS5180 / VS5190 Reducer 1 435-00, 435-01 Ful-Thane Binders VS5300 Urethane Activator VS5160, VS5170, VS5180, VS5190 ...Ful-Thane® 2K Urethane Binder (IB Quality) GENERAL DESCRIPTION A 5.0 lb/gal (600 g/l) VOC compliant, urethane single-stage topcoat that is easy-to-apply and provides outstanding durability for a variety of applications. The products referenced herein may not be sold in your market. Please consult your distributor for product availability. MIXINGJust got done spraying red Nason 2k Ful-thane single stage for the first time. I have some orange peel here and there along with some dirt in the hood. I have color sanded Centari and Delstar, but I am not sure how to tackle this with this newfangled urethane. I intend to hand wet sand with 1200 then buff.MIX RATIO Combine the components by volume (8:1:2). Mix thoroughly prior to activation. Component Ful-Thane® 2K Urethane Binder (IB Quality) Ful-Thane® 483-15TM 2K Urethane Activator Ful-Base® 441-20TM / 441-21TM / 441-22TM Reducer Volume 8 ADDITIVES Fisheye EliminatorProduct Details Packaging Information MSDS Technical Data Sheet Description A National Rule compliant, urethane single stage topcoat designed with superior hardness development for better cycle time, and improved metallic control providing thousands of cleaner, more vibrant colors.Nason Ful-Thane IS Quality Single-Stage Topcoat. A urethane single-stage topcoat that provides good quality and performance and features a wide range of sparkling metallic and rich solid colors. Click here to visit the product catalog.Ful-Thane 2K Urethane Binder (IB Quality) (PDF 362.8 kB) Nason Ful-Base Enamel Topcoat (IC Quality) (PDF 258.0 kB) Nason Ful-Cryl II 2K Acrylic Enamel Topcoat (ID Quality) (PDF 334.5 kB)MIXING COMPONENTS Mix 2 parts NasonXL Basecoat Color to 1 part NasonXL Reducer. Thin to spray viscosity of 16 secs with #4 Ford @ 77°F/25°C for spraying. Option for longer re-coating: Add 5% hardener to premixed basecoat Component Volume NasonXL Basecoat Color 2 NasonXL Reducers 1 (447-65 Fast, 447-75 Medium, 447-85 Slow) Package SizesIt is a single stage, but there is a clear your can mix with it or another to spray after it. dont use clear on single stage. you just put the single stage on, color sand with 1500 or 2000 grit, then buff to shine. if you want to use a clear coat, then you need to use a base/clear setup. personally, i wouldnt use a single stage paint on a car ...Ful-Thane® Urethane, one of the distinct paint qualities in the versatile Ful-Base® Multi-Leg Color System, provides an easy-to-apply, single-stage finish. Ful-Thane® offers outstanding durability for automobiles, trucks and commercial vehicles. Ful-Thane® 2K urethane is also available in Ful-Thane® 400-XX High Volume Factory Packages. 18-21 seconds in a Zahn #2 cup. 4 hours at 70°F. Solid colors: Apply 1 medium wet coat, flash to tack, apply 1 full wet coat. Metallic colors: Apply 2 medium-wet coats. Allow to flash 5-10 minutes between coats. Apply a third and final “mist” coat to even the metallic. Refer to the product Technical Data Sheet for complete directions for use.MSDS Technical Data Sheet Description A urethane single-stage topcoat that is easy-to-apply and provides outstanding durability for a variety of applications. Features Solventborne Easy to apply Outstanding durability Product Details Available Sizes Mixing Instructions Application Instructions ApplicationMIXING COMPONENTS Ful-Thane® HS Urethane Topcoat (IG Quality) Ful-Base® 430-XX Tints Ful-Thane® HS 435-95™ Urethane Binder Ful-Thane® 483-52™ Activator Ful-Thane® 483-54™ Accelerator (Required) MIX RATIO Combine the components by volume (3:1). Mix thoroughly prior to activation. Component Volume Ful-Base® 430-XX Tints Ful-Thane® 435-91™ 2K Urethane Binder Ful-Thane® 483-15™ 2K Urethane Activator Ful-Base® 441-20™ Reducer (Low-Temp) Ful-Base® 441-21™ Reducer (Mid-Temp) Ful-Base® 441-22™ Reducer (High-Temp) MIX RATIO Combine the components by volume (8:1:2). Mix thoroughly prior to activation. Component Volume Ful-Thane ...how do you mix nason base coat properly? it state to mix 8:1/2:4, none of the mixing cups i've got have an 1/2 mark on it. the only way i can think to mix it properly is to double the amount of color and reducer in oz's to get a whole oz in activator, which ends up being way to much paint for one coat.Product Details Packaging Information MSDS Technical Data Sheet Description A National Rule compliant, urethane single stage topcoat designed with superior hardness development for better cycle time, and improved metallic control providing thousands of cleaner, more vibrant colors.Nason Full-Thane lists the ratio as 8:1:2 My mix cups have 8:1:1 Using the '5' scale the distance between the 1:1 is 3/8". Will adding 3/8" mark to the last column give me an 8:1:2 ratio? View attachment 1715764917Detailed Description. Activator; Ful-Base 483-56 Low VOC Activator is used to mix Nason Ful-Thane 2K Urethane Topcoat (IS Quality), a 2.8 lbs/gal (340 g/l) VOC compliant, urethane single-stage topcoat that provides good quality and performance and features a wide range of sparkling metallic and rich solid colors.

Part 401-20-4. 1 qt Paint. Designed to enhance the depth and color of Ful-Thane factory packaged colors, Ful-Thane 2K Urethane single-stage colors and Ful-Cryl II mix colors. Specifications.. Sen

nason ful thane 2k urethane single stage mixing ratio

MIX RATIO Combine the components by volume (4:1:2). Mix thoroughly prior to activation. Component Volume Ful-Thane® 2K Urethane Topcoat (IS Quality) 4 Ful-Base® 483-56™ Low VOC Activator 1 Ful-Base® 441-60™ / 441-66™ / 441-68™ Reducer 2 ADDITIVES Fisheye Eliminator Add ½ to 2 oz Nason® 495-02™ Low VOC Fisheye Eliminator per ready ...Single Stage Topcoat ; Thinner ; ... FUL-THANE URETHANE SS BINDER "IS" 2.8 Gallon. ... SELECTSEAL 2K URETHANE SEALER - BLACK Gallon. Item #: 422-52 01.To enhance depth of color and provide a custom look, Ful-Thane® 401-20™ 2K Integrated Clear may be used. Mix one quart of catalyzed and reduced Ful-Thane® 401-20™ 2K Integrated Clear with one quart of activated and reduced color. Both are mixed 8:1:2. Do not use Ful-Thane® 401-20™ 2k Integrated Clear as a topcoat clear.Nason Finishes recommends using a ratio of 8:1/2:4, or 8 parts of Nason base coat to 1/2-part base coat activator to 4 parts base coat reducer. Failure to mix the paint properly can clog your spray gun. If you’re using aerosol cans, the paint should be properly mixed in the can for you, so skip this step. What is the mixing ratio for Nason paint?Application. Solid colors: Apply 1 medium wet coat, flash to tack, apply 1 full wet coat. Metallic colors: Apply 2 medium-wet coats. Allow to flash 5-10 minutes between coats. Apply a third and final “mist” coat to even the metallic.Do not use under any urethane paints other than Nason® Ful-Thane® 2K Urethane. Use same reducer for Bond-Seal™ as recommended for the Nason® single-stage topcoat to be applied. DRY TIMES To topcoat (for Nasco™ and Ful-Base® Topcoats): 10 minutes, but within 8 hours PHYSICAL PROPERTIES All Values Ready To Spray Max.Description. A National Rule compliant, Factory Package Snow White urethane single stage topcoat designed with superior hardness development for better cycle time, and improved metallic control providing thousands of cleaner, more vibrant colors. Ful-Thane 2K Urethane is the Nason brand’s premium single-stage paint that is easy to apply and ...Dupont Fleet book, page by page. If you are on a PC click on any of the. images and the images will pop up. You can hit next and the whole or most of the page will turn into a gallery.pre-formulated flat/mat clears are SOOOOOOOOO much easier on bigger jobs and all overs. all you do is mix and go. you can adjust the flatness by how many coats and reducer, again so much easier than a flattening ratio with an additive. i've done a few with sikkens mat clear with no problems, now give me a 2 component system where i have to mix some single stage and flattener in it and i cant ...Axalta Nason FulCryl II Acrylic Enamel Gallon Mix Item#: NAS ID 01. An acrylic enamel single-stage topcoat that provides very good gloss, chip resistance and durability for excellent performance characteristics. Please contact store for the proper price suffix for your color. Stock or paint code text may be added in the cart.MIXING COMPONENTS Ful-Thane® HS Urethane Topcoat (IG Quality) Ful-Base® 430-XX Tints Ful-Thane® HS 435-95™ Urethane Binder Ful-Thane® 483-52™ Activator Ful-Thane® 483-54™ Accelerator (Required) MIX RATIO Combine the components by volume (3:1). Mix thoroughly prior to activation. Component Volume we were going to use the Nason ful-thane , but our supplier suggested the Imron. I was amazed at how well it sprayed. You can plow that stuff on & it will not run. Im seriously thinking about using it when I do my truck. you can even get it in Flat, Semigloss, or regular gloss. RM's Uno is good also, I like the way it lays down, & it seems to last.Additive: FEE: 2-4 oz 495-01™ per RTS gal. Accelerator: 2-4 oz 483-18™ per RTS gal. Viscosity: 20-21 seconds in a Zahn #2 cup: Pot Life: 4 hours at 70°FUS :ENGLISH Ful-Thane 2K 2K Urethane Activator 483-15 Section 4. First aid measures Wash out mouth with water. Remove dentures if any. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomitingItem#: NAS 400-50 01. Ful-Thane Factory Packaged Colors includes a selection of high volume urethane colors that provide outstanding durability for automobiles, trucks, and commercial vehicles. This remarkable finish provides excellent gloss, chip resistance and ease of application. GM Code 12 White 400-50 Gallon..

Popular Topics